Modular Systems > National Instruments > NI Cables
Or speak to a sales representative for additional information:
Phone:1-800-915-6216
Email:sales@apexwaves.com
777720-01 Request for Availablility
777720-01, 50-Pin, NI DAQ, SH-50-50 Shielded Cable
Need an Official Quote?
National Instruments 777720-01 Shielded Cable
Part Number 777720-01 is the identifying part number for the National Instruments SH-50-50 Shielded Cable. This cable is mainly used to connect a NI DAQ or Motion Control device to different accessories and terminal blocks. It is a part of NI’s digital signal conditioning and I/O connectivity product series and is used in special applications where signal deterioration is not allowed. The cable comes in a length of 1 m or 2 m.
The 777720-01 features a 50-pin female connector with a spade terminal grounding strap on one end and a 50-pin female connector with a ring terminal grounding strap on the other end The connectors are wired pin-to-pin with a 25 twisted pair cable. To set up and use the 777720-01, you would need the following: the installation guide, a compatible NI device, a number 1 Philips-head screwdriver, 3 in. 50-to-50-pin ribbon cable (comes inside the kit), and replacement brackets with spade terminals (NB and AT), that are also included in the kit.
To install the 777720-01, first, you must replace the bracket on the board with the bracket from the SH-50-50 kit. Note that, you must first turn off the computer, remove the board from the computer, and then remove the screws that attach the bracket to the board. One important thing to consider is that the 50-pin connector on your board might have small plastic key inserts for use with military-polarized connectors. Since this is incompatible with the SH50-50 cable, it should be removed. You can gently press a pencil or a pen tip on the release tab in the center of the key insert. After this, you should connect the SH50-50 cable to a 50-pin board.
To install the 777720-01 on a 50-pin board, you must first install the board in a slot on your computer. This is followed by connecting the 50-pin connector of the shielded cable to the board I/O connector. Then, you must connect the 50-pin connector with the ring terminal grounding strap to your accessory. You can use an extender for the 3-inch ribbon cable for better flexibility.
| Part Number | 777720-01 |
|---|---|
| Model Name | SH50-50 |
| Part Type | Shielded Cable |
| Cable Length | 1 m or 2 m |
| Connector Type | 50-pin |
| Works With | NI DAQ or Motion Control Devices |
| Part of | NI’s Digital Signal Conditioning and I/O Connectivity Product Series |
| Internal Wiring | Pin-to-pin with a 25 twisted pair cable |
| Compatible Devices | PCI-6503 or PC-DIO-24 |
| Warranty | 2-3 years |
Why Buy From Apex Waves:
Verified
"Hand carrying parts to fedex directly to make sure I get them overnight. Great service"
"They were very helpful to get me the test equipment that I need."
777720-01
Modular Systems > National Instruments > NI Cables
777720-01, 50-Pin, NI DAQ, SH-50-50 Shielded Cable
1-800-915-6216
- Description
- Technical Specifications
National Instruments 777720-01 Shielded Cable
Part Number 777720-01 is the identifying part number for the National Instruments SH-50-50 Shielded Cable. This cable is mainly used to connect a NI DAQ or Motion Control device to different accessories and terminal blocks. It is a part of NI’s digital signal conditioning and I/O connectivity product series and is used in special applications where signal deterioration is not allowed. The cable comes in a length of 1 m or 2 m.
The 777720-01 features a 50-pin female connector with a spade terminal grounding strap on one end and a 50-pin female connector with a ring terminal grounding strap on the other end The connectors are wired pin-to-pin with a 25 twisted pair cable. To set up and use the 777720-01, you would need the following: the installation guide, a compatible NI device, a number 1 Philips-head screwdriver, 3 in. 50-to-50-pin ribbon cable (comes inside the kit), and replacement brackets with spade terminals (NB and AT), that are also included in the kit.
To install the 777720-01, first, you must replace the bracket on the board with the bracket from the SH-50-50 kit. Note that, you must first turn off the computer, remove the board from the computer, and then remove the screws that attach the bracket to the board. One important thing to consider is that the 50-pin connector on your board might have small plastic key inserts for use with military-polarized connectors. Since this is incompatible with the SH50-50 cable, it should be removed. You can gently press a pencil or a pen tip on the release tab in the center of the key insert. After this, you should connect the SH50-50 cable to a 50-pin board.
To install the 777720-01 on a 50-pin board, you must first install the board in a slot on your computer. This is followed by connecting the 50-pin connector of the shielded cable to the board I/O connector. Then, you must connect the 50-pin connector with the ring terminal grounding strap to your accessory. You can use an extender for the 3-inch ribbon cable for better flexibility.
| Part Number | 777720-01 |
|---|---|
| Model Name | SH50-50 |
| Part Type | Shielded Cable |
| Cable Length | 1 m or 2 m |
| Connector Type | 50-pin |
| Works With | NI DAQ or Motion Control Devices |
| Part of | NI’s Digital Signal Conditioning and I/O Connectivity Product Series |
| Internal Wiring | Pin-to-pin with a 25 twisted pair cable |
| Compatible Devices | PCI-6503 or PC-DIO-24 |
| Warranty | 2-3 years |
Why Buy From Apex Waves
"The business transaction was super easy and friendly."
"Hand carrying parts to fedex directly to make sure I get them overnight. Great service"
"They were very helpful to get me the test equipment that I need."
| Delivery: | UPS, FedEX and DHL – Free FedEx Ground on all orders Overnight, Next Day Air or Expedited shipping options available International delivery available Same day shipping for in-stock on location |
| Warranty: |
All of our products are covered by our Apex Waves Warranty. ✓ 3 Year Warranty - New Surplus Parts ✓ 2 Year Warranty - Refurbished Parts |
| Returns: | No hassle return policy. Dedicated customer service team. |
| Payment: |
|
| Quick Quotes: | Receive Price & Availability Today! |
| Calibration: | Ask About Our Tiered Calibration Levels |
| Option & Modules: | Confirm Your Requirements or Versions |
| Repair: | Cost & Lead Time Available Upon Request for Service Repair Evaluation: $150 |
| Share this page: |
|
